MIL-HDBK-115 Us Army Reverse Engineering Handbook Guidelines And ProceduresThis HANDBOOK, which provides the guidelines and procedures for performing reverse engineering, was created using current applicable laws and knowledge gained during a trial program from July 1985 to April 1987, and is based on experiences obtained from military and industry participants. This handbook is for guidance only and cannot be cited as a requirement.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78

MIL-HDBK-115B(ARMY)

PARAGARAPH                                                                                                      PAGE

5.26.2.8                    Quality assurance provisions............. 30

5.26.3                       Drawing maintenance.................. 31

5.27                          Quality control (QC).................31

5.27.1                       QC study.................... 31

5.27.2                       QC plan...................... 31

5.27.3                       QC inspections....................   31

5.27.4                       QC program..................... 32

5.28                          Quality assurance provisions (QAPS)........... 32

5.28.1                       QAPs objective..................  32

5.28.2                       QAPs required.................... 32

5.28.3                       QAPs not required................. 32

5.28.4                       Characteristic classification............... 32

5.29                          Documentation quality control................ 33

5.29.1                       QC review....................  33

5.29.2                       Inspection of drawings................ 33

5.29.3                       Limited physical configuration audit (PCA)....... 33

5.29.4                       Rejection criteria.................33

5.30                          Certificate of compliance.................. 33

5.31                          Production review....................  33

5.32                          Estimates...................... 33

5.33                          Make-or-buy...................  34

5.34                          Schedules...................... 34

5.35                          Should-cost.....................  34

5.35.1                       Data development.................. 34

5.35.2                       Actual costs and schedules................ 34

5.35.3                       Results.....................34

5.36                          Prototype production................ 34

5.36.1                       Prototype production objective............... 34

5.36.2                       Sub-contracting.................. 34

5.36.3                       Record maintenance................. 34

5.37                          Procurement....................  34

5.38                          Parts fabrication..................... 34

5.39                          Inspection and quality control................. 35

5.39.1                       Inspection..................... 35

5.39.2                       Quality control plan.................  35

5.40                          Assembly...................... 35

5.41                          Test......................... 35

5.41.1                       Validate concepts.................. 35

5.41.2                       Focus on conformance................  35

5.42                          Certificate of compliance............... 35

5.43                          Finalize TDP......................  35

5.43.1                       Formulate/deliver TDP...............  35

5.43.2                       Include changes.................. 35

5.43.3                       Procedures.................... 36

vi