MIL-HDBK-115 Us Army Reverse Engineering Handbook Guidelines And ProceduresThis HANDBOOK, which provides the guidelines and procedures for performing reverse engineering, was created using current applicable laws and knowledge gained during a trial program from July 1985 to April 1987, and is based on experiences obtained from military and industry participants. This handbook is for guidance only and cannot be cited as a requirement.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62 - 63 - 64 - 65 - 66 - 67 - 68 - 69 - 70 - 71 - 72 - 73 - 74 - 75 - 76 - 77 - 78

MIL-HDBK-115B(ARMY)

PARAGARAPH PAGE

5.20.2 Accuracy………………………………………………........ 20

5.21 Dimensional analysis………………………………………. 20

5.21.1 Dimensional analysis objective……………………………. 20

5.21.2 Considerations……………………………………………... 21

5.21.3 Process variation………………………………………….... 22

5.21.4 Establish tolerances……………………………………..…. 22

5.21.5 Lot determination………………………………………….. 23

5.22 Material analysis…………………………………………... 23

5.22.1 Material analysis objective…………………………...……. 23

5.22.2 Sample size……………………………………………….... 23

5.23 Electrical/electronic analysis…………………………….… 23

5.23.1 Electrical/electronic analysis objective……………………..23

5.23.2 Validate documentation………………………………….… 23

5.23.3 Complete documentation…………………………………... 24

5.23.4 Incomplete documentation……………………………….... 24

5.23.5 Design validation…………………………………………... 24

5.23.6 Environmental requirements………………………………. 25

5.23.7 Performance characteristics………………………..…….… 25

5.24 Engineering sketches and specifications………………....... 25

5.24.1 Engineering sketches and specifications objective…………25

5.24.2 Technical data requirements…………………………..…… 26

5.24.3 Test requirement specifications………………………….… 26

5.25 Level 3 drawings……………..………………………….… 26

5.25.1 Level 3 drawings objective……………….……………..… 26

5.25.2 Preparation…………………………………………………. 26

5.25.3 Content…………………………………………………...…26

5.25.4 Considerations……………………………………………... 27

5.25.5 Drawing media…………………………………………….. 28

5.25.6 Completeness of drawings…………………………………. 28

5.25.7 Computer-generated drawings…………………………..….28

5.25.8 Library files………………………………………………... 28

5.25.9 Drawing references………………………………………… 28

5.25.10 Quality control review……………………………………... 28

5.25.11 Candidate file inclusions……………………………………28

5.26 Producibility study…………..…………………………….. 29

5.26.1 Purpose…………………………………………………….. 29

5.26.2 Areas of consideration…………………………………..…. 29

5.26.2.1 Dimensions/tolerances……………………………………... 29

5.26.2.2 Materials………………………………………………..….. 29

5.26.2.3 Heat treatment………………………………………….….. 30

5.26.2.4 Finishes…………………………………………………….. 30

5.26.2.5 Clean and joining methods………………………………… 30

5.26.2.6 Coatings……………………………………………………. 30

5.26.2.7 Selection of standard parts/components…………………… 30